Damage may result. Clean under dust cap using a brush and rags. Clean area above cap as well. Chorus and Record freehubs are held on by the axle. The freehub body holds cartridge bearings. The axle is independent of the freehub. Freehub ratchet may be cleaned and re-greased.
The cartridge bearings may be tapped out and pressed by in with new bearings. If bearings are not to be replaced, do not removed bearings. Freewheel — Destructive Removal View Article. Trade Resources. Remove axle as during hub overhaul. See hub overhaul if you are unfamiliar with this process. Use a hex wrench to loosen and remove the freehub holding-bolt. Most brands are accessed through the right side, but a few are accessed through the left side. The bolt is typically very secure and may require much effort to loosen.
Note any spacer behind freehub. Gently remove any seal behind freehub body. Flush freehub in solvent, spinning body to remove dirt. Blow dry with compressed air. Use normal precautions when using compressed air. If no compressed air is available, allow freehub to sit until completely dry. Use a liquid lubricant in the back side and front. Spin freehub to work lube inside.
Grease freehub mounting-bolt. Install freehub and any spacer onto hub body. Thread in freehub mounting-bolt and secure fully. Tighten to about inch-pounds. If you are holding a wrench 6 inches from the bolt, apply 60 pounds of effort.
Assemble and adjust hub as with hub overhaul. These may be removed and replaced. Hold drive side axle securely in an axle vise. Hold non-drive side sleeve nut with cone wrench and loosen locknut counter-clockwise. Pressed-on axle cap will prevent locknut from being completely removed.
Get the Components. Tools you Need cassette tool. Adjustable Wrench. Parts we're Woking On cassette. Specific Tools Used. Inspect the internal splines of cogs. Look for a wide spline to mate with wide space in freehub body. Align splines and engage all cogs. Install spacers in same orientation as when removed. Grease threads of lockring and thread lockring into freehub. Install cassette lockring tool and install quick-release skewer.
Thread skewer nut on outside of lockring tool. Skewer acts as a holding device for freewheel tool. Turn remover clockwise until lockring is tight, at least inch-pounds approximately 40 Nm. For installing lockring, use of the sprocket chain whip tool is not required. Hold cassette cogs while turning tool counter-clockwise To install the cassette, lubricate the threads inside the cassette stack. Using two chain whip tools, place first chain whip on second or third cog, holding it clockwise.
Place second chain whip on first cog to rotate it counter-clockwise. This gives you better mechanical advantage. See image above. Rotate first cog counter-clockwise while holding the other chain whip.
This loosens first cog. Remove cog and pull off other cogs. Install cogs and spacers on freehub. Thread on smallest cog and secure clockwise with sprocket chain whip tool. Click to close full size. Item Description. Includes a stud to prevent the tool slipping under pressure. Coated handle for user comfort. Needs to be used with a chain whip to hold the cassette when unlocking the lock ring. We use Royal Mail for most of our parcels. Either First Class. Higher value items will be sent Tracked or Special Delivery which will require a signature on delivery.
Larger items will be sent using a courier service. All items are carefully packaged and are fully insured. Please allow 7 working days after despatch before contacting us for missing items. If your item arrives damaged or is incorrect please contact us as soon as possible so we can sort it out for you. Airmail Signed For and Airmail Airsure services depending which part of the world you are in.
These services are fully insured and delivery time is normally between working days. Brazil and some other countries can take up to 30 working days to arrive Please be aware that it's the buyers responsibility to pay any taxes or import duties charged by your country. In the event of you not receiving your package please allow 15 working days for Europe and 25 working days for the rest of the world after despatch before contacting us.
Please check the eBay Postage and Payments seciton at the top of the listing for postage costs to your country. Combined Postage We do combine postage for multiple items. But we do realise that this isn't for everyone.
Please note for other payment methods it greatly slows down our dispatch process as payments need to be checked and cleared and marked off.
Most items unless briefly out of stock at time of purchase are picked and packed daily. We pride ourselves on our turn-around, check our feedback!
All items will be safely packed and sent with whatever necessary packaging bubble wrap deemed necessary. Most of our packaging is recycled.
All items must be paid for ASAP. Non paying bidders will be referred to the eBay Dispute Resolution Centre. Use to cut cable outer casing. Cables and for pinching cable end caps and ferrules.
0コメント