Never store corrosive substances such as acid or alkali in this unit if the container cannot be sealed. These may cause corrosion of inner components or electric parts. Check the setting when starting up of operation after power failure or turning off of power switch. The stored items may be damaged due to the change of setting. Be careful not to tip over the unit during movement to prevent damage or injury.
Prepare a safety check sheet when you request any repair or maintenance for the safety of service personnel. This equipment is designed to be safe at least under the following conditions based on the IEC :. Ambient temperature 5 o C to 40 o C.
Other supply voltage fluctuations as stated by the manufacture;. Pollution degree 2 in accordance with IEC Front cover: A front cover opens when a bottom part is pulled to the front. Open this cover when you use cleaning of the condenser filter, a remote alarm terminal. Refer to page Control panel: Panel opens when the right top of the lower part cover is pushed. Light switch: This switch is used for turning the fluorescent lamp off and on.
Space for temperature recorder: An temperature recorder optional accessory can be mounted here. See page Fluorescent lamp: 40 W white lamp. See page 24 for replacement.
Lock: Turn the key clockwise through o to securely lock the door. Glass window: The window may have condensation in high humidity environment. Wipe off the condensation with a soft dry cloth. Dew receiver: The condensation on the outer door is accumulated on this dew receiver. Wipe off the water on the dew receiver with a cloth. Leveling foot: Adjust the height of the leveling feet by turning the screw bolts until the unit is level.
Caster: When installing the unit, the castors can be raised from the floor by using the leveling feet above. The maximum storage weight for each drawer is 40 kg. Shelf MPR only : Items to be stored in the chamber must be placed on the shelves. The maximum storage weight for each shelf is 50 kg. Do not put stored items directly onto the interior floor of the chamber.
Access port: This port allows temperature measurement cables to enter the chamber from outside. Exhaust air vent: Do not block this vent. If this vent is blocked, temperature regulation will become unstable. Do not place stored items in the path of the cold air. Intake air vent: Do not block this vent. Do not insert a finger or any foreign object into this vent as there is danger from the internal fan. Door switch: When a door opens, a fan for the cold circulation is stopped, and the leakage of the cold is prevented.
And, the check lamp of the door is turned on. Fixture: 2 fixtures are attached on the rear side of the unit. These keep adequate space between the unit and wall and also can be used for fixing the unit.
Evaporating tray: Defrost water from the evaporator accumulates on the tray and evaporates into the atmosphere. See page 23 for cleaning. Digital temperature indicator: This indicator shows the present chamber temperature or set temperature. Numerical value shift key : Pressing this key in the setting mode causes the numerical value to shift.
ON-OFF of key lock can be selected by pressing this key in the key lock mode. Digit shift key : Pressing this key in the setting mode causes the changeable digit to shift. Key lock is available by pressing this key for more than 5 seconds in the temperature display mode. Refer to page 20 for the key lock. Set key SET : Temperature setting mode is led by pressing this key. Once the key is pressed, the changeable digit is flashed. Pressing this key again after setting desired temperature, the setting is stored into computer memory.
If there is no key operation for 90 seconds during the temperature setting mode, the temperature setting mode is invalid automatically. See page 16 for the details. The remote alarm is also silenced by pressing this key. The buzzer cannot be stopped during remote alarm testing.
Condenser filter: This filter is for prevention of condenser clogged up. Clean the filter every 3 month. Remote alarm terminal: This is used to connect the unit to an exterior alarm to notify users of any malfunction. The key lock is set in OFF at the factory. In this case, a forced defrost cycle can be initiated. Ensure you do not inhale or consume medication or aerosols from around the unit at the time of maintenance. Follow the procedure below to replace the lamp. Turn off the fluorescent light switch and disconnect the power supply plug.
Remove all shelves or drawers. Disconnect the power supply plug. Remove the water-proof rubber. Remove the glow starter and replace with a new one. Replace the water-proof rubber. Cleaning of condenser filter 1. Page Troubleshooting Note: If the malfunction is not eliminated after checking the above items, or the malfunction is not shown in the above table, contact Sanyo sales representative or agent. The circuit breaker is activated.
The disposal of the unit should be accomplished by appropriate personnel. Always remove doors to prevent accidents such as suffocation. Page 29 The symbol mark and recycling systems described below apply to EU countries and do not apply to countries in other areas of the world. Page 32 Het symbool en de recycleersystemen die hieronder beschreven worden, zijn van toepassing op de landen in de EU en zijn niet van toepassing op landen in andere delen van de wereld. Uw SANYO product is ontworpen en gemaakt met materialen en onderdelen van hoge kwaliteit, die gerecycleerd en opnieuw gebruikt kunnen worden.
If an automatic temperature recorder is required, contact your Sanyo dealer. Please note that each recorder needs a exclusive fixture for mounting. An attached binder two pcs is used for the fan cover of the top of the chamber as the Fig. Route the capillary on the top of the chamber and fix it with the provided clip and screw. Remove the black rubber caps inside and outside on the access port located at the top corner of the unit and take the insulation out of the access port.
Pass the recorder sensor into the chamber through the access port. A battery for power failure alarm is included in the battery kit. Remove the top cover on the right front of the refrigerator top by unscrewing 4 screws. Page 37 Fig. Perform the setting for battery through the keys on the control panel of refrigerator.
Switch on the battery switch on the battery box. Page Safety Check Sheet Procedure to be adhered to in order to reduce safety risk indicated in b below. This manual is also suitable for: Mprr. Hold the handle when closing the door. This will reduce the likelihood of a trapped finger.
Never place your hand on the glass or use excessive force on the glass. Intentional force may break the glass resulting in injury from the broken glass. Do not touch the condenser directly when the filter is removed for cleaning. This may cause injury due to hot surface. Disconnect the power supply plug before moving the unit. Take care not to damage the power cord. A damaged cord may cause electric shock or fire. Dispose of any water in the evaporation tray completely before moving the unit.
Spilled or splashed water may cause current leakage or electric shock. Be careful not to tip the unit over during movement to prevent damage or injury. Disconnect the power plug when the unit is not used for long periods. Do not put the packing plastic bag used in the packaging within reach of children as suffocation may result.
If the unit is unplugged or the power to the unit is interrupted, do not restart the unit for at least 5 minutes. This protects the compressor. This inner cabinet is refrigerated by forced circulation of cooled air inside the chamber. Ensure that the intake and exhaust air vents are not blocked. Adequate space should be provided between the items inside the unit to allow air circulation. The temperature alarm may be operated at the time of first start-up.
The alarm will be canceled automatically when the chamber temperature will reach the set temperature. Check that the door is closed tightly. The door check lamp lights when the door is open. The alarm buzzer sounds two minutes after door opening. The buzzer can be canceled automatically when the door is closed. Always open and close the door gently.
Rough door operation may lead fall down of stocked items, incomplete closing, or damage of door gasket. Never store corrosive materials such as acid or alkali unless the container is completely sealed up. Corrosion may lead to failure of the unit in time. Once the chamber temperature has stabilized, put the items into the chamber in small batches to minimize the temperature increase.
Fix the shelves securely and make sure to place any materials on the shelves Do not place items on the floor of the chamber. If an instrument requiring a power source is placed inside the cabinet, the cable can be lead through the access port on the cabinet.
After installation, a rubber cap should be used to seal the access port. Failure to do this can affect the temperature uniformity inside the cabinet and lead the condensation on the outside of the access port.
In case condensation forms on the front glass or frame due to a high humidity environment, wipe if off with a soft and dry cloth. Do not clean the unit with scrubbing brushes, acid, thinner, solvents powdered soap, cleanser or hot water.
These agents can scratch the paint or cause it to peel. Plastic and rubber parts can be easily damaged by these materials, especially solvents. When a neutral detergent is used to clean the unit, wipe it up thoroughly with a cloth soaked in clean water. Check the condenser filter and clean it regularly. A dusty filter may cause temperature increase in the chamber or compressor failure.
This unit is equipped with a circuit breaker on the back. Make sure to switch ON this breaker before the unit starts to run. Following figures show the circuit breaker position. When the operation of the unit is stopped by this breaker, contact a dealer or a service station after disconnected the power supply plug. This equipment is designed to be safe at least under the following conditions based on the IEC :. Ambient temperature 5 o C to 40 o C.
0コメント